Pivot bolt and special nut for Brembo PS 13 and PS 16 master cylinders, also used for some hydraulic clutch lever pivot bolts

Not for early Cali 1100s fitted with solid brake lever pivot pins. Brembo ref. 110279850

 This part is due back in stock soon, call 01484 841395 to reserve yours

 10279850 GU10279850 10 27 98 50
 1027 9850 1027.9850 10.27.98.50

Piston ring set for Nikasil 83mm bores

These can be used with cast iron bores

 This part is due back in stock soon, call 01484 841395 to reserve yours

14060655-z 14060655 GU14060655 14 06 06 55
 1406 0655 1406.0655 14.06.06.55

88mm piston ring set for cast and Nigusil bore

3 ring set. Only for Cali 1100 frame prefixes KG and KH, for KC and KD prefixes see ENA30660

 This part is due back in stock soon, call 01484 841395 to reserve yours

18060601-z 18060601 GU18060601 18 06 06 01
 1806 0601 1806.0601 18.06.06.01

Piston ring compressing tool, compresses piston rings to fit into bore. Without this tool you risk snapping piston rings, the tool also speeds up the fitting of new rings

For 57mm - 125mm bores, supplied with hex key for bore adjustment. Not suitable for CARC models

 This part is available by special order, request a quote

Complete piston and barrel kit including gudgeon pin, piston rings and circlips. Piston is low compression

Components for 1 cylinder

 This part is available by special order, request a quote

29060201-z 29060201 GU29060201 29 06 02 01
 2906 0201 2906.0201 29.06.02.01

Used for camshaft sprocket pin and 5 speed gearbox selector pin

 1 in stock

 14234600 GU14234600 14 23 46 00
 1423 4600 1423.4600 14.23.46.00

Lightweight folding Tarozzi aluminium pillion footrest on zinc finish steel bracket footpeg. Footpeg is hollow with rubber Sleeve. Supplied with nyloc nut and washer.

A great way to tidy up the pillion footrests on your project bike

 Availability varies on this part, check availability

 01163620 GU01163620 01 16 36 20
 0116 3620 0116.3620 01.16.36.20

Dellorto PHF36 DD right hand carb. This is a flat top carb with 90° angle adapter for the throttle cable. Supplied with cable choke set up. Carb body is darker than earlier versions

44mm inlet manifold connection, includes accelerator pump. Supplied with single banjo connector. These can be fitted to T3, Convert, 1000 SP and T4 if FUA30611 is fitted.
Carb normally supplied in the following specification:

• 60/3 slide
• 130 main jet
• 50 idle jet
• 70 choke jet
• 8.5 gram float
  
  

   This part is available by special order, request a quote

   28112650 GU28112650 28 11 26 50
   2811 2650 2811.2650 28.11.26.50

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Dellorto PHF36 DS left hand carb. This is a flat top carb with 90° angle adapter for the throttle cable. Supplied with cable choke set up. Carb body is darker than earlier versions

44mm inlet manifold connection, includes accelerator pump. These can be fitted to T3, Convert, 1000 SP and T4 if FUA30611 is fitted.
Carb normally supplied in the following specification:

• 60/3 slide
• 130 main jet
• 50 idle jet
• 70 choke jet
• 8.5 gram float
  
  

   This part is available by special order, request a quote

   28112651 GU28112651 28 11 26 51
   2811 2651 2811.2651 28.11.26.51

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Ignition pickup and tacho sensor

Connector plug has two male spades. Also known as phase sensor. Used on models with the large Marelli P8 ECU. No longer available from Guzzi. Note 90° angle where cable exits sensor. See ENA90141 for O ring used to fit this part

 1 in stock

 29721660 GU29721660 29 72 16 60
 2972 1660 2972.1660 29.72.16.60